Tools/Maintenance

Supports bikes at the seat and chain stays - Lifts rear wheel to allow maintenance and repair of drive-train - Adjustable hook height and angle - Stable wide footprint

Replacement threaded cap for Abbey Hanger Alligment Gauge Tool.

Replacement shaft for Micro Bearing Press - 1/4" shaft diameter - 12" length

Replacement feeler gauge for the Abbey Hanger Alligment Gauge Tool.

For use with 1/4" Micro Bearing Press Shaft

Replacement pins, these are original equipment chain pins for our chain tool, they also work as an alternate to the Campagnolo UT-CN300 11spd chain tool, Shimano CN-34 and CN-32 Sold in pairs.

If you've been working on your bike for a while, you are well acquainted with the simple derailleur hanger and it's importance to your shift quality. The HAG has been a cornerstone tool in the Abbey catalog for a long time and it's accuracy is unparalleled in the industry. But what if you just want to check hanger alignment in a quick easy manner without removing your rear derailleur? Enter the preHAG! This simple tool is meant to quickly see if the derailleur cage is parallel to the cogs. It simply presses onto the largest cog and hangs down to give you a reference plane to judge if your bike is square with the world. This isn't meant to replace the accuracy of a HAG, just add an additional step that doesn't require any disassembly of the bike for those pre ride once overs.

Replacement 6/8mm Hex bit for both the Abbey BBQ Wood Handled Pedal Wrench and the Team Issue Pedal Wrench.

Replacement shaft for Modular Bearing Press

For use with 1/2" Bearing Press Shaft

For use with 1/2" Micro Bearing Press Shaft

For use with 1/2" Modular Bearing Press Shaft

The magnetic saddle height bullet ensures you get an accurate center at the bottom bracket by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate.

The magnetic saddle height bullet ensures you get an accurate center at the bottom bracket by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate.

1/8" mid plate, needed to use the Decade chain tool with wide 1/8" track and single speed chains.

For use with the Decade Chain Tool this AXS Mid Plate is required for the SRAM AXS Road and the new MTB Transmission Flat Top chains. This part is not needed for other 12spd chains from various manufacturers. The mid plate is visually differentiated from the other Decade mid plates by three dots on the face of the plate.

Our bit holder has been quite the hit with customers so we have started offering them as a stand alone part or with a set of bits. The bit holder is a machined aluminum part with a strong magnet in the base. The holder will retain the individual bits as well as affix the holder to a steel object. Holder made in Bend Oregon.

Replacement shaft for Modular Bearing Press

The Stu Stick is a 44-gram rotor truing tool. Whether you want to slip it into your hydration pack for that enduro mountain bike ride or travel the world working with one of the staples of cross racing, it's up to the task. You can even use it to crack open a beer after you're done with the day's fun. - Weight: 44g - Made of aluminum

These gems are machined to precisely fit the preload adjuster cap on all modern 24mm spindle Shimano cranks. The finger spline offers good leverage to install, remove, or adjust the preload cap. We also added a 5mm hex in the center should you need a little extra leverage that a hex key provides. These are also compatible with our fit kits and with the addition of a saddle height bullet can be used to more accurately measure saddle height.

Suspension service is a specialty within bicycle repair, and it takes specialized tools to perform this work. One of the things that any factory tech will tell you is nice to have are sockets specifically made or altered for the low profile hex on the top of each fork leg. The lead-in or chamfer on a standard socket will greatly decrease the contact between tool and part and can easily scratch or deform those nuts. For years shops have been grinding down their sockets to remove the chamfer. The problem is that you're still often left with a loose-fitting socket that is still prone to chewing up those delicate parts. That's why we started from scratch. We made our sockets from billet aluminum to exacting tolerances to keep these parts in good shape. Fully CNC-machined with zero lead-in, they make the specialty that is suspension service a little bit easier. They feature a 3/8" square drive for use with your favorite torque wrench as well as finger splines to help run the top caps into the fork legs with those oil soaked hands. We also kept them short (1" or 25mm for all sizes) to reduce the chance of them slipping off of the top cap under torque. - Made from billet aluminum to exacting tolerances to keep form damaging the suspension - Finger splines so you can thread it easily by hand - 3/8" square drive - Short (1"/25mm for all sizes) to reduce the chance of them coming off of the top cap under torque - Made in Bend, Oregon Applications - 24mm socket - used on SRAM top caps - 26mm socket - used on Marzocchi and Reverb sealheads - 27mm socket - used on Fox and X-Fusion top caps - 30mm socket - used on the RS-1 SRAM sealhead removal tool as well as a handful of other forks. - 6-size set covers most modern suspension forks on the market: 24, 26, 27, 28, 30 and 32mm

This is a 13mm socket made specifically for the bleeders on modern Fox forks. These bleeders are built just like a top cap, with minimal height of the hex drive. So it's a perfect application for our original chamferless sockets. Use these to install the fenders that mount behind the bleeders or when servicing your fork. Socket uses a 3/8" square drive. Compatibility: Fox fork models 36,38 and 40 equipped with bleeders.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. The Fork Seal Press is built with modern tight fitting fork seals in mind. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.

Bearing drift designed for the SRAM DUB crank platform and use with the Abbey Bike Tools Modular bearing press. SRAM recently launched a new crank platform called DUB to improve bearing durability and compatibility that modern frames have dictated. This 28.99mm spindle and its press fit bottom bracket requires some special drifts to install correctly. We worked with the crew at SRAM to develop tools for this and came up with some simple and important tweaks from a standard bearing drift. These drifts have a tapered boss that forces the small O ring into its gland. A normal drift with a square boss can easily tear the fragile O ring that helps with bearing durability. So this basic modification makes sure your bottom bracket retains the durability it was designed to have. - Comes as a set of two drifts