Tools/Maintenance

The new 8-Bit System is a group of multi-tools designed to work together to solve most trailside fixes. They are lightweight, strong, versatile, and small enough to fit in a jersey pocket or riding tool wrap. Three multi-tools begin the 8-Bit System: 8-Bit Chainbreaker + Utility Knife Multi-Tool, 8-Bit Tire Lever + Rim Dent Remover Multi-Tool, and 8-Bit Pack Pliers. A total of 22 functions between the three tools will keep you rolling to the next town or trailhead. - 17 functions: spoke wrench; valve core wrench; flat head #3.5 and Phillips #2 screwdriver bits; 2, 2.5, 3, 4, 5, 6, and 8mm hex; and T10, T25 Torx-compatible bits; install and remove master links; clear tire sealant clogs from valve stem; tighten valve stem lock nut - Magnets keep all bits in place - Ball detent swivel head helps access hard-to-reach places - Handle doubles as breaker bar for extra torque when head is bent - 8mm hex bit tested to over 40 Nm torque - Pliers works with 9-, 10-, 11- and 12-speed master links and chains (not compatible with Campagnolo 12-speed chains) - Master Link storage is compatible with SRAM PowerLock Link, Shimano Quick-Link, KMC Missing Link and other similar master links (not compatible with Connex Links by Wipperman)

- E-bike socket designed for installing and removing compatible cassettes on Bafang hub-drive motors without removing motor wiring - Center clearance for E-Bike wiring is 0.812". 12-spline 23mm OD tool fittings - Made in the USA

Wheels Manufacturing open bore adapters are used to press sealed cartridge bearings into place. The adapters are machined with one step to correspond to the bearing OD, which fits in to the center of the sealed bearing and an outside diameter to accommodate the bearing's outer diameter. Size: [Bearing inner diameter] x [Bearing outer diameter] Note: If only one dimension is given, that is the outer diameter of the adapter, with no inner diameter step

Wheels Manufacturing Over Axle Adapters are used for pressing your most commonly used bearing sizes into place. Each represents an excellent addition to the Press-4 Bearing Press. - Adapters sold individually

Wheels Manufacturing Sealed Bearing Extractor - 10mm Fits the following bearings: - 6704 - 6804 - 6904

An essential tool for your shop. Designed to work specifically with the 36mm OD IsoStrut from Fox. Proprietary tool for Trek bikes equipped with 2020-2023 IsoStrut. Details: - Refer to the Service Manual for assembly instructions and service - Contains 2 presses, one for each end - Compatible with a standard headset press to install both bushings at once

Dial in your dream geometry Adjust head tube angle one degree slacker or steeper on compatible Trek mountain bikes with angle-adjust cups and this tool. Product details - Refer to Service Manual for assembly instructions and service - Includes upper and lower gauge - 8mm metric wrench needed for alignment sold separately

The Trek Pro BITS Multi-Tool packs all of your essential riding tools into one compact kit, including a tubeless tire reamer. Plus it gives you the storage you need for tire plugs and a quick-link. Your go-to multi-tool for any ride, anywhere Don't get stranded without your tools! Trek Pro BITS Multi-Tool packs all the tools you need to fix a mechanical when you're on the road or trail. It also comes equipped with storage for key items like tubeless tire plugs (included) and a quick-link (sold separately). PRODUCT DETAILS - Includes 2, 2.5, 3, 4, 5, 6, and 8mm hex tools, T25, Phillips and flat screwdrivers, tubeless tire reamer, and a chain tool - The "ghost key" includes size 0, 1, and 2 spoke wrenches, valve core removal tool, and valve extender wrench - Storage for quick-links (sold separately) and tubeless tire plugs (included) - Precise, durable tools made from laser cut steel, a cast steel chain tool, and the tool body is anodized aluminum with a plastic storage compactment - Lightweight and compact design makes this tool kit easy to store nearly anywhere

- For all TRP and Tektro hydraulic braking systems - Non-corrosive mineral oil - Increased Boiling point to 270 degrees C - Decreased viscosity for better fluid flow

Shimano Hydraulic Disc Brake Fluid - Non-corrosive mineral oil that offers excellent heat expansion properties - Mineral oil will not absorb water from the air - Not caustic and is non-toxic

Shimano Genuine Professional disc brake bleed kit Includes: - TL-BR002 Funnel unit for ST series Road Brake lever (M7 thread bleed port) - TL-BR003 Funnel unit for BL series MTB brake lever (M5 thread bleed port) - TL-BR001 Syringe unit - 4-pcs set of Bleed Blocks (Piston spacer) Features: - New oil spill guard lid with an integrated oil stopper holder - Improved syringe unit design now using a stronger threaded tube joint and revised locking clip - Bleeding instructions available for download under 'Documents & Links' below

Shimano Genuine disc brake bleed syringe kit Features: - Strong threaded tube joint - Bleed nipple tool - Locking clip - Bleeding instructions available for download under 'Documents & Links' below

Shimano Genuine disc brake bleed Funnel unit for ST type Road brake lever (M7 thread bleed port) Features: - Oil spill guard lid with an integrated oil stopper holder - Funnel base - Bleeding instructions available for download under 'Documents & Links' below

Shimano Genuine disc brake bleed Funnel unit for BL type MTB brake lever (M5 thread bleed port) Features: - Oil spill guard lid with an integrated oil stopper holder - Funnel base - Bleeding instructions available for download under 'Documents & Links' below

To adjust preload on Hollowtech II cranksets

SRAM Bleeding Edge Tool. - Use with Avid or SRAM Pro Bleed Kit

DOT 5.1 brake fluid is compatible with all SRAM and Avid hydraulic disc brakes - Brake Fluid Type: DOT 5.1 - Bottle Size (Brake Fluid): 4 oz - Application (Brake Fluid): Disc Brakes

- Pro Mineral Oil V2 bleed kit includes: (2) premium syringes, M4 fittings, bleed blocks, Torx tool, crowfoot, Bleeding Edge Fitting, and with or without Maxima mineral brake oil. Compatible with SRAM DB8 and Maven brakes - Standard Mineral Oil V2 bleed kit includes: (2) standard syringes, M4 fittings, bleed blocks, Torx tool, crowfoot, Bleeding Edge Fitting and with or without Maxima mineral brake oil. Compatible with SRAM DB8 and Maven brakes - Pro DOT V2 Brake bleed Kit includes: (2) premium syringes/fittings, bleed blocks, Torx tool, crowfoot, Bleeding Edge Fitting and with or without DOT 5.1 hydraulic fluid. Compatible with SRAM/Avid hydraulic DOT brakes - Standard DOT V2 brake bleed kit includes: (2) standard syringes/fittings, bleed blocks, Torx tool, crowfoot, Bleeding Edge Fitting and with or without DOT5.1 hydraulic fluid. Compatible with SRAM/Avid hydraulic DOT brakes

- Pro Mineral Oil V2 bleed kit includes: (2) premium syringes, M4 fittings, bleed blocks, Torx tool, crowfoot, Bleeding Edge Fitting, and with or without Maxima mineral brake oil. Compatible with SRAM DB8 and Maven brakes - Standard Mineral Oil V2 bleed kit includes: (2) standard syringes, M4 fittings, bleed blocks, Torx tool, crowfoot, Bleeding Edge Fitting and with or without Maxima mineral brake oil. Compatible with SRAM DB8 and Maven brakes - Pro DOT V2 Brake bleed Kit includes: (2) premium syringes/fittings, bleed blocks, Torx tool, crowfoot, Bleeding Edge Fitting and with or without DOT 5.1 hydraulic fluid. Compatible with SRAM/Avid hydraulic DOT brakes - Standard DOT V2 brake bleed kit includes: (2) standard syringes/fittings, bleed blocks, Torx tool, crowfoot, Bleeding Edge Fitting and with or without DOT5.1 hydraulic fluid. Compatible with SRAM/Avid hydraulic DOT brakes

• Service kits include air can seals and wiper • Available for RockShox air rear shocks--Ario, Monarch, Monarch RT3, DebonAir and Monarch Plus

- 50 hour service kit for Deluxe and Super Deluxe rear shocks - Includes air can seals, piston seal, and glide rings

- Use to install fork dust seals

Service kits include dust seals, foam rings, oil seals, air and damper o-rings needed for basic service.

• Removes and installs all RockShox 1/2mm rear shock eyelet bushings and mounting hardware

RockShox's Suspension Oil comes in different weights to match the most popular suspension fork and shock setups.

- Essential mechanic tools to properly service and maintain all RockShox products - Clamps the shock body for easy maintenance

The tire lever, though seemingly one of the simplest and most basic of cycling tools, is one commonly used by almost every cyclist, and unfortunately, one often responsible for unnecessary frustration. Really, what is more fun than flatting far away from home, being thrilled you lugged that spare tube and pump, and then having your tire levers snap in two? Pedro's award-winning, universally loved tire levers feature molded box construction and a proprietary plastic composite blend that makes them the strongest levers available. The unique chisel tip shape easily inserts beneath the tire bead and the slightly thicker shape keeps the lever securely in place. Additionally, the bold shape of the lever and helpful dual spoke hooks makes removal of even the tightest tires a simple task. - Award-winning and universally loved - Molded box construction and proprietary plastic blend makes these the strongest levers available - Chisel tip shape is easy to insert beneath the bead and the slightly thicker shape keeps the tire lever from slipping - Bold shape makes it easy to remove the tightest of tires without bending or breaking

Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-1 FEATURES - 4mm, 5mm, and 6mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit

Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-3 FEATURES - 2mm, 2.5mm, and 3mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit

Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.

Park's Anti-Seize Compound reduces friction in threaded and press fit connections for easy assembly and disassembly. It's ideal for bottom brackets, pedal threads, headset cups, seatposts, quill stems and much more. This compound also seals and protects parts from corrosion and rust under the most extreme conditions.

The BBT-22 is a shop-quality tool for installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-22 ensures maximum engagement with the bottom bracket cup. It can be used with a 3/8-inch drive torque wrench, a 3/8-inch ratchet driver, a 32mm wrench, the Park FRW-1 Freewheel Remover Wrench (sold separately), or a 1-inch wrench.

The BKM-1.2 Hydraulic Brake Bleed Kit will bleed most models of mineral oil-based hydraulic bicycle disc brakes, including models made by Shimano®, Magura®, TRP®, Tektro®, Trick Stuff®, SRAM® DB8, Campagnolo®, Promax®, and Clarks®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKM-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, a bleed funnel, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: -  Two 20 mL syringes -  Two hose assemblies with shutoff clips -  One hose assembly with integrated fitting for bleed nipples such as those found on Shimano® mineral oil brake systems -  One open-ended hose assembly -  Bleed funnel with stopper -  Two 10 mm/12 mm universal bleed blocks -  Two 11 mm bleed blocks -  Two adjustable syringe holders -  M4 x 0.7 adapters — SRAM® DB8, Trick Stuff®, Campagnolo® (x2) -  M5 x 0.8 adapter — Formula™ Cura™, Tektro®, Hayes® (x2) -  M6 x 0.75 adapter — Magura® -  M6 x 1.0 adapters — universal (x2) -  M6 x 1.0 adapter — Promax® -  M7 x 0.75 adapter — Shimano® -  Hose compression sleeve — universal -  Fluid disposal bag -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKM-1.2 is for mineral oil-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For brakes using DOT fluid use the Park Tool BKD-1.2 Hydraulic Brake Bleed Kit — DOT.

Keep your work area tidy with Park's Bench Top Small Parts Holder. It's constructed from rugged stainless steel with a clear, acrylic hinged top that lets you see what's inside. It also includes 4 removable bins that are perfectly sized to hold small parts, cable end caps, grease and whatever other little items you can think of.

A clean bike is a happy bike! Park Tool's Bike Cleaning Brush Kit is a four-piece brush set designed specifically to clean bicycles. Ergonomically designed and featuring dual-density, sure-grip handles, the BCB-4.2 kit includes: • 1 GSC-1 Gear Clean Brush • 1 Tapered Detail Brush • 1 Frame Cleaning Sponge/Bristle Brush • 1 Soft Bristle Soaping Brush

The BBP-1.2 quickly and accurately installs bottom bracket bearings, cups and adapters into press fit bottom bracket shells. The complete set of precision-machined bushings matches up with most common bottom bracket cup dimensions. The press assembly features a comfortable handle, oversized shaft, and magnetic back plate for quick and easy assembly. - The complete set of precision-machined bushings match up with most common bottom bracket cup dimensions - The press assembly features a comfortable handle, oversized shaft, and magnetic back plate for quick and easy assembly - Magnetic quick-release design allows for fast installation and removal of tool - Organized in a convenient storage case - Compatible with bottom bracket shell widths from 68mm to 150mm 6 sets of precision-machined bushings (in 9 sizes) to fit these bottom bracket configurations: - 386EVO - BB30 - BB86 - BB90 - BB92 - BB95 - BB121 - BMX Mid - BMX Spanish - OSBB - PF41 - Press Fit 24 - PressFit GXP® - BBright™ Direct Fit - PF30 BBright™ Press Fit - Shimano® Press Fit - All Press Fit DUB®

A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 16-notch tool fittings, including Wheels Mfg™ Thread Together & FSA® MegaEvo®. Manufactured in-house by Park Tool, anodized for easy identification, and featuring a ratchet/torque wrench-compatible 3/8" drive. Fits 16-notch bottom bracket tool fittings with a major diameter of 48–50 mm and a minor diameter of 46.4 mm, including: - FSA® MegaEvo® - Wheels Mfg™ Thread Together Note: Does not fit Hope™ BSA30

The Bottom Bracket Wrench removes and installs Shimano Hollowtech II, Race Face X-type, FSA MegaExo, Campagnolo Ultra-Torque and TruVativ Giga X-pipe bottom brackets. Laser cut for a precise fit, one end of the BBT-9 securely engages the 16 cup notches, while the other end engages the 8 internal splines of the crankarm adjustment cap.

A worn bicycle chain can cause poor shifting and expensive drivetrain damage. The Park Tool CC-4.2 Chain Checker is a drop-in gauge that measures chain wear accurately. It contacts the chain in three places, eliminating guesswork. Compatible with 5 to 13-speed and single-speed chains, it indicates wear at 0.5%, 0.75%, and 1.0%, matching manufacturer replacement recommendations. - Measures bicycle chain wear accurately, preventing expensive drivetrain damage - Laser-cut design contacts the chain at three points, providing quick and precise wear measurement - Compatible with 5 to 13-speed derailleur chains and single-speed chains - Indicates chain wear at 0.5%, 0.75%, and 1.0%, aligning with manufacturer recommendations for replacement

Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut

Park's Crank Puller is for removing crankarms on Shimano's splined, oversize, pipe-billet bottom brackets. It employs a long handle and a fine thread for the leverage and torque needed to remove tight arms. Park's unique rotating tip ensures smooth operation and long life. (The CCP-44 does not fit standard square or tapered bottom brackets.)

A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.

An alignment gauge is essential for diagnosing and repairing bent or misaligned derailleur hangers, often the source of shifting problems. The DAG-3 features an all-new design, engineered and built to be light, accurate, and versatile. The sliding indicator can measure derailleur hanger alignment against bicycle rims of any size and rotates out of the way to clear seat stays, racks, and other obstacles, allowing 360-degree measurement. The long, precision-extruded aluminum body is built to exacting tolerances and provides ample leverage for making adjustments. - Compatible with 16" to 29"+ wheels (ISO/ETRTO rim sizes from 317 to 630+) - Replaceable M10 threaded tip - Low-profile head fits low clearance thru-axle derailleur hangers and Shimano Direct Mount hangers - Length: 16.5" (420mm) - Weight: 22.75 oz. (645g)

- Brake holder features M5, M6 & passthrough holes for attaching all disc brake mounting styles as well as most rim brake caliper styles - 1-1/8" steerer tube features star nut for retaining top cap and spacers - 2" flared cone for compatibility with tapered steerer tubes - Compatible with 1-1/8" threadless stems only—not compatible with threaded headset/quill stem setups

Suspension maintenance and tuning require tools designed for a precise fit. The SKT-6 from Park Tools is a shop-quality set of six flat-faced sockets designed for use with common suspension fork fittings. Ideal for use with Park Tool Torque Wrenches, the 3/8-inch drive sockets are forged from tough chrome vanadium steel and chrome plated for lasting durability. - 24, 26, 27, 28, 30, 32mm flat-faced sockets - All sockets are 3/8" drive - Note: 27mm socket is tapered for better access on Suntour suspension forks

Forged and machined, the ZP-5 is ideal for closely cutting zip ties and many other materials in tight spaces.

12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.

HPG-1 Park Tool High Performance Grease is proprietarily blended to meet the demanding needs of today’s high performance bicycles and high end components. -Superior adherence and extended lubrication life -Extreme temperature range: -20°F to 540°F (-29°C to 282°C) -Highly water resistant -Perfect for high end applications including precision ground and ceramic bearings, pivots and suspension components 4-ounce (113 g) tube

Park's Hydraulic Brake Piston Press is used to set or reset the piston(s) inside hydraulic disc brake calipers during installation, maintenance and repair. Just push it into the caliper to wedge the piston into place. It's made of tough tool steel with a comfortable and oversize rubber handle for a great grip.

Many chains use a master link that allows the chain to be installed and removed by hand. While master links don't require traditional chain tools, over time, dirt and corrosion can make it difficult to separate them by hand. Park's Master Link Pliers make removing and installing these master links quick and easy. Simply insert the specially sized jaws into the link and squeeze the vinyl-coated handles!

Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.

A great time-saver! Park Tool's Nipple Driver is neatly designed to self-center and drive conventional nipples quickly and easily during wheel building. The ND-1 is built with a comfortable, dual-density grip and lined with precision bronze bearings to ensure a long, smooth running life. It works with rims up to 50mm deep.

Engineered for fit, function, and leverage, these L-shaped shop-quality Torx compatible wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Torx compatible drivers at each end - Includes T6, T8, T10, T15, T20, T25, T30, and T40 - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization

Park's PolyLube is specifically formulated to protect bearing components. Its Polyurea grease has extremely high shear strength to protect bottom brackets, headsets, pedals and hubs. Use it on threads, seatposts, stems and cables, too. It's also safe for fork seals, and repels water.

Park's PolyLube is specifically formulated to protect bearing components. Its Polyurea grease has extremely high shear strength to protect bottom brackets, headsets, pedals and hubs. Use it on threads, seatposts, stems and cables, too. It's also safe for fork seals, and repels water.

Park’s Professional Cable And Housing Cutter is specifically for use on derailleur and brake cables and housing. It even makes quick work of hard-to-cut shift-cable housing. Its cold-forged, heat-treated-steel handles won't bend and its precision-ground jaws cut perfectly every time. Its dual-density molded grips are specially contoured for superior comfort and control. Plus, there’s a built-in cable-end crimper and a forming hole for reforming housing ends.

Fills gaps and helps retain non-threaded parts like Press-fit bottom bracket parts, sealed bearings etc. Notice: Park Tool AP-1 Adhesive Primer must be used to prep all components, fasteners and carbon fiber surfaces prior to application of Park Tool threadlockers or retaining compound. Failure to do so could result in permanently bonded parts.

Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs

Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)

The SHX-1 Slide Hammer Extractor is a professional solution specifically designed for removing press fit cartridge bearings from bicycle components. Utilizing expanding collets, an extendable shaft, and a substantial (960g) slide hammer, the SHX-1 securely yet forcefully drives out cartridge bearings with targeted impact. The SHX-1 is compatible with cartridge bearings with inner diameters from 6 to 32 millimeters, covering most press fit applications found on bicycles including hubs, suspension linkages, and bottom brackets. - Set of 5 expanding collets covers most bicycle bearing IDs from 6mm to 32mm - Slide hammer shaft is extendable from 6.5" (165mm) to 13" (233mm) for additional force when needed - Organized in a convenient storage case